1Introduction & Contraindications ... 2Specifications ...
10FIRST TIME SETUPPower Cord3. Connect the power cord.Plug the socket end of thepower cord into the ACpower cord connector on theback of the REMstar L
11FIRST TIME SETUPAssemblingthe Circuit5. Assemble the circuit. To use the System, you will need thefollowing accessories in order to assemble the r
12FIRST TIME SETUPAssemblingthe Circuitb. If you are using a mask with a built-inexhalation port (e.g., Respironics Monarch®Mini Mask), connect the ma
13ACCESSORIESAdding Oxygento the SystemHumidifiers are available from your home care provider. Thehumidifiers may reduce nasal dryness and irritation
14Using a DCPower SystemYou can also use the REMstar LX in a stationary recreational vehicle,boat or motor home with a 12 volt DC power source. The R
15ROUTINE USEConnectingthe Circuit1. Connect the circuit. Before each use, examine the flexible tubing for anydamage or debris. If necessary, clean th
16ROUTINE USEPressing the Ramp button will reducethe air pressure when you are tryingto fall asleep. The air pressure willgradually increase until you
17TRAVELING WITH THE SYSTEMPackingthe SystemSecurity StationsChecking thePower CordChanging theVoltage and FusesCAUTION!When traveling, the optional c
18TRAVELING WITH THE SYSTEMChanges inElevationElevation changes can affect the pressure being delivered by theREMstar LX. At elevations less than 2,5
19ROUTINE MAINTENANCECleaning andReplacingthe FiltersCAUTION!The gray pollen filter should be cleaned at least once every two weeksunder normal usage
2INTRODUCTIONIntended UseThe REMstar LX and REMstar Plus LX CPAP Systems are for the treat-ment of adult Obstructive Sleep Apnea (OSA) only. The REMst
20ROUTINE MAINTENANCEChangingthe FusesCAUTION!If the REMstar LX does not turn ON when the power cord is plugged in,the fuses may need to be replaced.
21ROUTINE MAINTENANCECleaningthe SystemWARNING!ReorderingTo avoid electrical shock, unplug the REMstar LX before cleaning.Do not immerse the REMstar L
22ROUTINE MAINTENANCEServiceWARNING!The REMstar LX System does not require routine servicing.• If symptoms of sleep apnea recur, contact your physici
23TROUBLESHOOTINGThe table below lists common problems you may have with the REMstar LX System and possiblesolutions to those problems. If none of th
24TROUBLESHOOTINGProblemThe air flow from theREMstar LX seems warm.The REMstar LX ismaking a faint hummingsound when the air flow isturned off.The noi
25Respironics, Inc.® warrants that the REMstar® LX CPAP device shall befree from defects of workmanship and materials and will perform inaccordance wi
26LIMITED WARRANTYThe REMstar LX and REMstar Plus LX CPAP devices carry a two-yearwarranty. A warranty/comment card should be included with thismanua
27SUMMARYThis summary is not intended to replace the complete user instructions. The entire manualshould be read and understood before operating the R
28SUMMARYStep 4 Connect the flexible tubing,exhalation port, and mask.Adjust the mask and headgear.Step 5 Turn the air flow on or off bypressing the
Fill in the information below when you receivethe REMstar® LX or REMstar Plus LX CPAP System.REMstar LX Serial No.: (Located on th
3SpecificationsDimensions: 10.00" x 5.50" x 4.75" (25x14x12 cm)Weight: < 5 lb. (2.27 kg)Operation Transport & StorageTemperature
4WARNINGS & CAUTIONS• This device is intended for adult use only.• This device is not intended for life support.• All CPAP devices have the potent
5UNPACKING THE SYSTEMAfter unpacking the System, check to make sure you have everything shown here:Note: REMstar Plus LX devices are equipped with a t
6SYSTEM FEATURESFilter CapTimeMeterAC PowerConnectorDC PowerConnectorAC VoltageSelectorAir OutletRampButtonPressureOn / Off ButtonSignalLightPressure
7SYSTEM FEATURESAC Power Connector... Connect the AC power cord here.AC Voltage Selector ...This switch is used to select the AC volta
8FIRST TIME SETUPWARNING!Do not use the REMstar LX CPAP System until an appropriateprofessional adjusts the settings!To use the system, you may need t
91. Verify the voltage selection. Make sure the voltage selector switchon the back of the unit is set correctly (e.g., United States andCanada: 115V).
Comments to this Manuals